Building the Trim Tab

I started this session by first dressing the edges of the left elevator skeleton parts, but that only took about 30 minutes, so I decided to find something else to work on.  Since those parts are waiting on priming, the only thing I have left to start on is the trim tab.  I read the plans and decided to give it a go and try to get the end tabs bent, and some work done of the trim tab itself. I managed to almost finish the trim tab assembly tonight 🙂

After dressing up the edges of those left elevator parts, I laid them up on the shelf and dug out the trim tab parts.  First we have to start off by bending the trailing edge of the skin for the trim tab, and this is done exactly like the elevators.  So I set up my bending brake  and put a very smooth and gradual bend on the trailing edge, and made sure it was straight with the spar in place.

Granted, I took my time on this, I got it done in about 20 minutes or so.  I have been reading up on bending these tabs for a while now, and watched the Orndorff videos, so I was pretty prepared to begin.  I started out by making some bending blocks that fit into the end of the trim tab.  I used the tab itself to draw an outline on a piece of 2×4 and then cut the shape out on my bandsaw.  I made two sets because the bends on each end are at slightly different angles.

With the bending blocks made up, its time to get to bending the trim tab! I start out by inserting the blocks and clamping everything down to my work table nice and tight so it doesn’t move during bending.

We start out by bending the bottom tab first, and overlapping it with the top tab, so that the top tab folds over the bottom, helping to keep water and debris from getting into the trim tab.   I used a block of wood in my hand to get the bend started and once I had it at about a 45 degree angle, I use a small hammer against my wood block to help shape the metal.  This way, I am using the soft face of my wood block against my tab and the bending block instead of the hard metal face of the hammer.  This keeps from dinging, denting and scuffing the aluminum.  I took lots of time and did this very slowly, using small light taps with the hammer against my block to bend the metal.  Once I had the bottom tab bent up to a 90 degree bend, I did the exact same to the top tab, bending it to overlap the bottom.   I am really happy with the results.

Now that we have the inboard side of the trim tab bent, it time to move to the outboard.  These tabs are MUCH smaller than the inboard side, so I had to take extra caution on these little suckers.  They would be easy to crack if you work the metal to much.  Eventually, I got them folded up, overlapping the bottom tab with the top just like on the other side.  I stuck the spar into the trim tab and clecoed it in a few spots to check my work, and I am happy with how it turned out!

Outboard Tabs

Inboard Tabs

After having a good victory on the tab bending, I still felt good enough to continue on working. The plans have us mount the E-717 and E-718 trim tab horns to the bottom of the trim tab.  E-717 has 3 of the 4 holes pre-drilled, so its easy to line up.  Then I just clamped E-718 to E-717 with some side clamps, and then use one of the clevis pins and hinges from my electric trim kit to make sure the holes were lined up properly in the trim tab horns.  Once everything was lined up, I back drilled both of the trim tab horns to the trim tab.

So, next up was to fully cleco on the spar, and then attach the hinge bracket so it can be back drilled.  I studied the plans and made a few alignment marks on my E-721 trim tab hinge.  Vans gives the measurements to the center of the hole in the skin/spar so its easy to mark the hinge with a sharpie, and then line up the cross hairs with the center of the hole.  I also marked the entire centerline of the hinge to the measurements Vans gives with a sharpie so I could align every single hole.  Once I had them all aligned, I used some cleco side clamps to hold it all together.  Once I had the hinge clamped on firmly, I started back drilling using the holes in the E-619-PP trim tab skin as my guides.

Once I had the hinge back drilled, I flipped the trim tab over and match drilled all the holes on the bottom to the spar.  Now, the plans has us disassemble the trim tab, so that we can trim off any excess from the trim tab horns, as well as the excess from the inboard side of he E-721 hinge.  I went ahead and trimmed off the very little bit of excess on the E-718 and E-717 trim tab horns, and smoothed the edges with a scotchbrite pad, and then did the same to the little bit of excess on the E-721 hinge.  I figured this was a good place to stop, so I called it a night.  I still need to deburr the holes, dress the edges of the trim tab parts and then dimple it all.  I am contemplating if I should prime the trim tab or not, not sure yet.  Here’s all the photos I took tonight:

This slideshow requires JavaScript.

Heres the Google Photos Link: https://goo.gl/photos/nFHQysMhoQBFDwdJA

Hours Worked: 4
Tagged , , . Bookmark the permalink.

Leave a Reply