https://aalamsalon.com/kiss8x9ez54 Holy crap…its been a LONG time since I did any real work on the RV-7. Like nearly 7 months. Life’s been a bit busy, I bought a 1973 Cessna Cardinal 177RG and have been flying the wings off of it, and that has taken up some time on the build, in addition to work, and family. But, with the daylight hours dwindling, and flying weather getting sparse, its back to building!
go to siteCarisoprodol 350 Mg For Sleep Anyways, the last place I left off, I had to finish up Alodining some wing ribs, and then get my wings in their stands. I ended up going down to Aircraft Spruce a few months back (In the Cardinal of course!!) to pick up some more Alumaprep and Alodine. So I mixed it up tonight. Here is what I am using for the mix ratios:
go herehttp://jannaorganic.co.uk/blog/2025/04/03/hecpl5d55n3 Alumaprep bath:
source link 1 Gallon of Alumaprep 33 concentrate mixed with 3 gallons of distilled water. Makes 4 gallons.
get linkfollow link Rinse the parts off to get rid of dust and grime. Scuff with maroon scotchbrite a little if needed during the rinse. Then soak for 7 to 10 minutes in the bath.
go to sitehere Rinse parts in cold water to remove alumaprep.
follow follow site
https://musicboxcle.com/2025/04/og8it3czk6 In the photo above, I had to use a rib and a glass jar to help hold down the other 6 ribs. The bubbles from the Alumaprep during its cleaning causes the aluminum to float!
see urlhttps://www.psychiccowgirl.com/si44htmk Alodine bath:
https://semichaschaver.com/2025/04/03/c4mbzbb 1 Gallon of Concentrate Alodine mixed with 2 gallons of distilled water. Makes 3 gallons.
https://reggaeportugal.com/0d3v11rtuhttps://reggaeportugal.com/667m6h05 After the alumaprep bath and rinse, soak parts in Alodine bath for 7 to 10 minutes. Remove and rinse in cold water to remove excess alodine and then let air dry.
watch
https://audiopronews.com/headlines/zzlkt158 
follow link And the obligatory photo that shows to the FSDO that I am actually the sucker building this plane…..apron,, gloves and all. I did remove my safety glasses for the photo though.
Buy Cheap Clonazepam 1Mgget link I was able to get all of the wing main ribs and wing end/nose ribs done and set out to air dry. It was good to get back down here and work on this project and start making progress again. I have decided to not spray primer on the ribs, except maybe the nose ribs. I think I will prime them since they will be fully enclosed and potential traps for moisture. Here’s how they ended up:
get link
https://kirkmanandjourdain.com/evdt3ut 
https://townofosceola.com/qdenf5hh5f0 And here is the entire photo album from tonights work. Not many photos since it was just alodining. I think I will start working on the wing stands next.
https://www.annarosamattei.com/?p=d5y3k6i
https://www.annarosamattei.com/?p=xtceixv
https://www.anonpr.net/ol4k5se6qsource Google Photos Link: https://photos.app.goo.gl/e5yTndwHvwCXRT6L9 https://etxflooring.com/2025/04/gk9g40fm Hours Worked: 2
https://semichaschaver.com/2025/04/03/wpmi04gbo
https://colvetmiranda.org/vsdgd8db56 I was wondering where you went!
go to sitehttps://audiopronews.com/headlines/0wj2oju Yeah, finally getting back at it! Stayed pretty busy this summer and didn’t have much free time to spend unfortunately. But, with the short days, I am getting back down in the shop to get some work down on the RV-7. 🙂
follow url