Completing The Wing Access Plates

go site Since I am still waiting on the aileron pushrods, I figured I’d knock out a few of the last straggling tasks.  This session was all about the access plates for the wings. I wanted to get the nutplates riveted onto the access holes in the bottom wing skins, and also … Continue reading go site

https://wonderpartybcn.com/wl9i6k1irvh

Dimpling the Bottom Wing Skins

here A little change of pace! I’m back to dimpling skins.  This time around I managed to get all 4 of the bottom skins dimpled: 2 inboard and 2 outboard.  I didn’t snap any photos of this work, but I did get a time lapse of the entire session.  It’s not … Continue reading

https://genevaways.com/lm17thpe9u

Mounting the Left Aileron BellCrank

follow link Not really a whole lot to report on this session, I did manage to get the left wing bell crank installed and few wires ran though.  I’ve decided to not built a mounting bracket for the pitot / AOA tubes just yet. I think I may have an elegant solution, … Continue reading

Buy Cheap Ativan

Mounting the Left Aileron

Ativan 1 Mg Price It’s time to get the left aileron mounted! I’ll save all the details on this post, as those are all covered in the right wing mounting.  I’ll do a brief synopsis, and let the time lapse speak for itself. I started by cutting both of the spacers for the inboard … Continue reading

https://retailpanama.com/el4bhsmx2

Cradle Upgrades and Shop Work

https://serenitycareandcompassion.com/4zumhkc Made some big changes in the shop tonight, not to mention a milestone of getting the wings off their stands!  I started out by finishing up an upgrade to my wing cradle: Storage shelf!  Theres a bunch of space begging for a shelf between the two posts of the cradle. … Continue reading

click

Sometimes reviews don’t tell the truth

https://jahuss.com/g65yak5vw9 Well, I have some messed up aileron pushrods now. I decided to take my pushrods to be welded, after some concerns over the edge distance on one of the rivets.  I figured I would get them welded and call it good.  I found a local mobile welder that had great … Continue reading

https://estherbarniol.com/a4zg7kf8bv

Mounting the Right Aileron

https://www.starc.org/uncategorized/ogyi0yxmwb Getting some control surfaces mounted up! I was able to get the right aileron mounted onto the wing, and everything bolted in place and ready for me to do the rigging of this aileron.  I captured an overheard timelapse of the work here: I started out by pulling the right … Continue reading

watch

Assembling Right Wing Aileron Bell Crank

Buy Ambien Online Without A Prescription Some changes to the shop tonight, and its time to start working on the control surfaces.  I did manage to get the W-421 aileron bellcrank assembled and bolted onto the spar web, where I’ll next install the aileron.  I grabbed an overhead timelapse, since I am not sure where to … Continue reading

click here

Finishing Aileron Push Rods and Control Tubes

Buy Tramadol Online Without A Script Quick update and work session tonight.  The last long control tube has cured from its priming, and Its ready for the rod end to be riveted.  So, I grabbed the primer, and swirled some on the inside of the VA-111 rod end, and also on the mating surface. Then I … Continue reading

https://elien.ca/mp20flh0a

Aileron Push Rod Tubes – Part 3

go here Yeap.  Part 3.  This is a short session for tonight, but progress none the less. I also stopped by Ace Hardware and picked up another small can of oil based metal primer to finish off the other tube, where we ran short last night.  I did manage to completely assembly … Continue reading

https://jahuss.com/kmv28cyw37w